Nov 17 20:50:46 tisa kernel: acx100: It looks like you've been coaxed into buying a wireless network card
Nov 17 20:50:46 tisa kernel: acx100: that uses the mysterious ACX100/ACX111 chip from Texas Instruments.
Nov 17 20:50:46 tisa kernel: acx100: You should better have bought e.g. a PRISM(R) chipset based card,
Nov 17 20:50:46 tisa kernel: acx100: since that would mean REAL vendor Linux support.
Nov 17 20:50:46 tisa kernel: acx100: Given this info, it's evident that this driver is quite EXPERIMENTAL,
Nov 17 20:50:46 tisa kernel: acx100: thus your mileage may vary. Visit http://acx100.sf.net for support.
Nov 17 20:50:46 tisa kernel: acx100: Warning: compiled to use 16bit I/O access only (compatibility mode). Set Makefile ACX_IO_WIDTH=32 to use slightly problematic 32bit mode.
Nov 17 20:50:46 tisa kernel: acx_init_module: dev_info is: TI acx_pci
Nov 17 20:50:46 tisa kernel: acx_init_module: TI acx_pci.o: Ver 0.2.0pre8 Driver initialized, waiting for cards to probe...
Nov 17 20:50:46 tisa kernel: AMD756: dev 104c:9066, router pirq : 3 get irq :  9
Nov 17 20:50:46 tisa kernel: PCI: Found IRQ 9 for device 0000:00:0a.0
Nov 17 20:50:46 tisa kernel: acx_probe_pci: WARNING: ACX111 support is quite experimental!
Nov 17 20:50:46 tisa kernel: Found ACX111-based wireless network card at 0000:00:0a.0, irq:9, phymem1:0xefdfe000, phymem2:0xefdc0000, mem1:0xd2ac0000, mem1_size:8192, mem2:0xd2b40000, mem2_size:131072
Nov 17 20:50:46 tisa kernel: initial debug setting is 0x001b
Nov 17 20:50:46 tisa kernel: acx_select_io_register_set: using ACX111 io resource addresses (size: 56)
Nov 17 20:50:46 tisa kernel: hw_unavailable = 1
Nov 17 20:50:46 tisa kernel: acx_show_card_eeprom_id: EEPROM card ID string check found uninitialised card ID: this is a SpeedStream SS1021 or Gigafast WF721-AEX, no??
Nov 17 20:50:46 tisa kernel: acx_probe_pci: TI acx_pci: Using IRQ 9
Nov 17 20:50:46 tisa kernel: reset hw_unavailable++
Nov 17 20:50:46 tisa kernel: acx_reset_mac: enable soft reset...
Nov 17 20:50:46 tisa kernel: acx_reset_mac: disable soft reset and go to init mode...
Nov 17 20:50:46 tisa kernel: Firmware: '/etc/Netgear-WG311v2/TIACX111.BIN' not found. Trying alternative firmware.
Nov 17 20:50:46 tisa kernel: Trying to load firmware: '/etc/Netgear-WG311v2/FwRad16.bin'
Nov 17 20:50:46 tisa kernel: Allocated 76208 bytes for firmware module loading.
Nov 17 20:50:46 tisa kernel: not using auto increment for firmware loading.
Nov 17 20:50:46 tisa kernel: acx_write_fw: Firmware written.
Nov 17 20:50:47 tisa kernel: acx_write_fw (firmware): 0, acx_validate_fw: 0
Nov 17 20:50:47 tisa kernel: acx_reset_dev: boot up eCPU and wait for complete...
Nov 17 20:50:47 tisa kernel: acx_reset_dev: Received signal that card is ready to be configured :) (the eCPU has woken up)
Nov 17 20:50:47 tisa kernel: acx_reset_dev: Clean up cmd mailbox access area
Nov 17 20:50:47 tisa kernel: reset hw_unavailable--
Nov 17 20:50:47 tisa kernel: acx100: allocated net device wlan0, driver compiled against wireless extensions v16 and Linux 2.6.9
Nov 17 20:50:47 tisa kernel: ******************************************
Nov 17 20:50:47 tisa kernel: ************* acx_init_mac_1 *************
Nov 17 20:50:47 tisa kernel: ******************************************
Nov 17 20:50:47 tisa kernel: ==> Get the mailbox pointers from the scratch pad registers
Nov 17 20:50:47 tisa kernel: CmdMailboxOffset = 1dd00
Nov 17 20:50:47 tisa kernel: InfoMailboxOffset = 1de86
Nov 17 20:50:47 tisa kernel: <== Get the mailbox pointers from the scratch pad registers
Nov 17 20:50:47 tisa kernel: CommandParameters = [ 0xd2b5dd04 ]
Nov 17 20:50:47 tisa kernel: InfoParameters = [ 0xd2b5de8a ]
Nov 17 20:50:47 tisa kernel: ERROR 2 trying to open firmware image file '/etc/Netgear-WG311v2/RADIO16.BIN': file not found - make sure this EXACT filename is in eXaCtLy this directory!
Nov 17 20:50:47 tisa kernel: WARNING: no suitable radio module (/etc/Netgear-WG311v2/RADIO16.BIN) found to load. No problem in case of a combined firmware, FATAL when using a separated firmware (base firmware / radio image).
Nov 17 20:50:47 tisa kernel: acx111_init_packet_templates: Init max packet templates
Nov 17 20:50:47 tisa kernel: acx111_create_dma_regions: set up acx111 queue memory configuration (queue configs + descriptors)
Nov 17 20:50:47 tisa kernel: dump queue head:
Nov 17 20:50:47 tisa kernel: length: 24
Nov 17 20:50:47 tisa kernel: tx_memory_block_address (from card): 17DC0
Nov 17 20:50:47 tisa kernel: rx_memory_block_address (from card): 10FC0
Nov 17 20:50:47 tisa kernel: rx1_queue address (from card): 101B4
Nov 17 20:50:47 tisa kernel: tx1_queue address (from card): 104F4
Nov 17 20:50:47 tisa kernel: get_mask 0x00004182, set_mask 0x00000000
Nov 17 20:50:47 tisa kernel: Don't know how to get sensitivity for radio type 0x16, please try to add that!
Nov 17 20:50:47 tisa kernel: Got sensitivity value 0
Nov 17 20:50:47 tisa kernel: Got antenna value 0x0A
Nov 17 20:50:47 tisa kernel: Got regulatory domain 0x41
Nov 17 20:50:47 tisa kernel: get_mask 0x00000000, set_mask 0x00000000 - after update
Nov 17 20:50:47 tisa kernel: new ratevector: 82 84 8b 0c 12 96 18 24 2c 30 48 60 6c
Nov 17 20:50:47 tisa kernel: SSID = STABF2BF3, len = 9
Nov 17 20:50:47 tisa kernel: Beacon length:69
Nov 17 20:50:47 tisa kernel: SSID = STABF2BF3, len = 9
Nov 17 20:50:47 tisa kernel: hw_unavailable--
Nov 17 20:50:47 tisa kernel: acx100: form factor 0x01 ((mini-)PCI / CardBus), radio type 0x16 (Radia), EEPROM version 0x0005. Uploaded firmware 'Rev 0.4.11.4' (0x03010101).
Nov 17 20:50:47 tisa kernel: creating /proc entry driver/acx_wlan0
Nov 17 20:50:47 tisa kernel: creating /proc entry driver/acx_wlan0_diag
Nov 17 20:50:47 tisa kernel: creating /proc entry driver/acx_wlan0_eeprom
Nov 17 20:50:47 tisa kernel: creating /proc entry driver/acx_wlan0_phy
Nov 17 20:50:47 tisa kernel: acx_probe_pci: TI acx_pci.o: Ver 0.2.0pre8 Loaded Successfully